This is a list of publishedThis list generally excludes draft versions. International Organization for Standardization (ISO) standards and other deliverables.ISO deliverables include "specifications" (ISO/PAS, ISO/TS), "reports" (ISO/TR), etc, which are not referred to by ISO as "standards". For a complete and up-to-date list of all the ISO standards, see the ISO catalogue.
The standards are protected by copyright and most of them must be purchased. However, about 300 of the standards produced by ISO and IEC's Joint Technical Committee 1 (JTC 1) have been made freely and publicly available.
ISO 16000 – ISO 16999 ISO/TR 16015:2003 Geometrical product specifications (GPS) - Systematic errors and contributions to measurement uncertainty of length measurement due to thermal influences ISO 16016:2016 Technical product documentation – Protection notices for restricting the use of documents and products ISO 16020:2005 Steel for the reinforcement and prestressing of concrete – Vocabulary ISO/IEC 16022:2006 Information technology - Automatic identification and data capture techniques - Data Matrix bar code symbology specification ISO/IEC 16023:2000 Information technology - International symbology specification - MaxiCode ISO 16032:2004 Acoustics – Measurement of sound pressure level from service equipment in buildings – Engineering method ISO 16034:2002 Ophthalmic optics – Specifications for single-vision ready-to-wear near- vision spectacles ISO 16039:2004 Road construction and maintenance equipment – Slipform pavers – Definitions and commercial specifications ISO 16054:2000 Implants for surgery – Minimum data sets for surgical implants ISO/TR 16056 Health informatics - Interoperability of telehealth systems and networks ISO/TR 16056-1:2004 Part 1: Introduction and definitions ISO/TR 16056-2:2004 Part 2: Real-time systems ISO/TS 16058:2004 Health informatics – Interoperability of telelearning systems ISO 16059:2007 Dentistry - Required elements for codification used in data exchange ISO 16061:2015 Instrumentation for use in association with non-active surgical implants – General requirements ISO 16063 Methods for the calibration of vibration and shock transducers ISO 16063-1:1998 Part 1: Basic concepts ISO 16063-11:1999 Part 11: Primary vibration calibration by laser interferometry ISO 16063-12:2002 Part 12: Primary vibration calibration by the reciprocity method ISO 16063-13:2001 Part 13: Primary shock calibration using laser interferometry ISO 16063-15:2006 Part 15: Primary angular vibration calibration by laser interferometry ISO 16063-16:2014 Part 16: Calibration by Earth's gravitation ISO 16063-17:2016 Part 17: Primary calibration by centrifuge ISO 16063-21:2003 Part 21: Vibration calibration by comparison to a reference transducer ISO 16063-22:2005 Part 22: Shock calibration by comparison to a reference transducer ISO 16063-31:2009 Part 31: Testing of transverse vibration sensitivity ISO 16063-32:2016 Part 32: Resonance testing – Testing the frequency and the phase response of accelerometers by means of shock excitation ISO 16063-33:2017 Part 33: Testing of magnetic field sensitivity ISO 16063-41:2011 Part 41: Calibration of laser vibrometers ISO 16063-42:2014 Part 42: Calibration of seismometers with high accuracy using acceleration of gravity ISO 16063-43:2015 Part 43: Calibration of accelerometers by model-based parameter identification ISO 16063-45:2017 Part 45: In-situ calibration of transducers with built in calibration coil ISO 16069:2004 Graphical symbols - Safety signs - Safety way guidance systems (SWGS) ISO/IEC 16085:2006 Systems and software engineering - Life cycle processes - Risk management ISO 16087:2013 Implants for surgery – Roentgen stereophotogrammetric analysis for the assessment of migration of orthopaedic implants ISO 16103:2005 Packaging - Transport packaging for dangerous goods - Recycled plastics material ISO 16106:2006 Packaging - Transport packages for dangerous goods - Dangerous goods packagings, intermediate bulk containers (IBCs) and large packagings—Guidelines for the application of ISO 9001 ISO 16134 Earthquake- and subsidence-resistant design of ductile iron pipelines ISO 16140 Microbiology of the food chain – Method validation ISO 16140-1:2016 Part 1: Vocabulary ISO 16140-2:2016 Part 2: Protocol for the validation of alternative (proprietary) methods against a reference method ISO 16142 Medical devices – Recognized essential principles of safety and performance of medical devices ISO 16142-1:2016 Part 1: General essential principles and additional specific essential principles for all non-IVD medical devices and guidance on the selection of standards ISO 16142-2:2017 Part 2: General essential principles and additional specific essential principles for all IVD medical devices and guidance on the selection of standards ISO/TR 16153:2004 Piston-operated volumetric instruments – Determination of uncertainty for volume measurements made using the photometric method ISO 16155:2006 Ships and marine technology – Computer applications – Shipboard loading instruments ISO 16165:2013 Ships and marine technology - Marine environment protection - Terminology relating to oil spill response ISO/IEC TR 16166:2010 Information technology – Telecommunications and information exchange between systems – Next Generation Corporate Networks (NGCN) – Security of session-based communications ISO/IEC TR 16167:2011 Information technology – Telecommunications and information exchange between systems – Next Generation Corporate Networks (NGCN) – Emergency calls ISO 16175 Information and documentation - Principles and functional requirements for records in electronic office environments ISO 16175-1:2010 Part 1: Overview and statement of principles ISO 16175-2:2011 Part 2: Guidelines and functional requirements for digital records management systems ISO 16175-3:2010 Part 3: Guidelines and functional requirements for records in business systems ISO 16192:2017 Space systems - Experience gained in space projects (lessons learned) - Principles and guidelines ISO/TS 16195:2013 Nanotechnologies – Guidance for developing representative test materials consisting of nano-objects in dry powder form ISO/TR 16196:2016 Nanotechnologies – Compilation and description of sample preparation and dosing methods for engineered and manufactured nanomaterials ISO/TR 16197:2014 Nanotechnologies – Compilation and description of toxicological screening methods for manufactured nanomaterials ISO 16212:2017 Cosmetics – Microbiology – Enumeration of yeast and mould ISO/TR 16218:2013 Packaging and the environment - Processes for chemical recovery ISO 16232 Road vehicles – Cleanliness of components of fluid circuits ISO 16232-1:2007 Part 1: Vocabulary ISO 16232-2:2007 Part 2: Method of extraction of contaminants by agitation ISO 16232-3:2007 Part 3: Method of extraction of contaminants by pressure rinsing ISO 16232-4:2007 Part 4: Method of extraction of contaminants by ultrasonic techniques ISO 16232-5:2007 Part 5: Method of extraction of contaminants on functional test bench ISO 16232-6:2007 Part 6: Particle mass determination by gravimetric analysis ISO 16232-7:2007 Part 7: Particle sizing and counting by microscopic analysis ISO 16232-8:2007 Part 8: Particle nature determination by microscopic analysis ISO 16232-9:2007 Part 10: Particle sizing and counting by automatic light extinction particle counter ISO 16232-10:2007 Part 10: Expression of results ISO 16239:2013 Metric series wires for measuring screw threads ISO 16245:2009 Information and documentation - Boxes, file covers and other enclosures, made from cellulosic materials, for storage of paper and parchment documents ISO 16249:2013 Springs – Symbols ISO 16254:2016 Acoustics – Measurement of sound emitted by road vehicles of category M and N at standstill and low speed operation – Engineering method ISO/IEC 16262:2011 Information technology – Programming languages, their environments and system software interfaces – ECMAScript language specification ISO 16269 Statistical interpretation of data ISO 16269-4:2010 Part 4: Detection and treatment of outliers ISO 16269-6:2014 Part 6: Determination of statistical tolerance intervals ISO 16269-7:2001 Part 7: Median - Estimation and confidence intervals ISO 16269-8:2004 Part 8: Determination of prediction intervals ISO/TS 16277 Health informatics – Categorial structures of clinical findings in traditional medicine ISO/TS 16277-1:2015 Part 1: Traditional Chinese, Japanese and Korean medicine ISO 16278:2016 Health informatics – Categorial structure for terminological systems of human anatomy ISO 16284:2006 Ophthalmic optics – Information interchange for ophthalmic optical equipment ISO/TR 16310:2014 Symbol libraries for construction and facilities management ISO/IEC 16317:2011 Information technology – Telecommunications and information exchange between systems – proxZzzy for sleeping hosts ISO/IEC/IEEE 16326:2009 Systems and software engineering - Life cycle processes - Project management ISO 16331 Optics and optical instruments – Laboratory procedures for testing surveying and construction instruments ISO 16331-1:2017 Part 1: Performance of handheld laser distance meters ISO 16336:2014 Applications of statistical and related methods to new technology and product development process - Robust parameter design (RPD) ISO/IEC 16350:2015 Information technology - Systems and software engineering - Application management ISO/IEC 16353:2011 Information technology – Telecommunications and information exchange between systems – Front-end configuration command for NFC-WI (NFC-FEC) ISO 16355 Applications of statistical and related methods to new technology and product development process ISO 16355-1:2015 Part 1: General principles and perspectives of Quality Function Deployment (QFD) ISO 16355-2:2017 Part 2: Non-quantitative approaches for the acquisition of voice of customer and voice of stakeholder ISO 16355-4:2017 Part 4: Analysis of non-quantitative and quantitative Voice of Customer and Voice of Stakeholder ISO 16355-5:2017 Part 5: Solution strategy ISO/TR 16355-8:2017 Part 8: Guidelines for commercialization and life cycle ISO/TR 16379:2014 Tissue-engineered medical products – Evaluation of anisotropic structure of articular cartilage using DT (Diffusion Tensor)-MR Imaging ISO/IEC 16382:2000 Information technology – Data interchange on 12,7 mm 208-track magnetic tape cartridges – DLT 6 format ISO/IEC 16388:2007 Information technology - Automatic identification and data capture techniques - Code 39 bar code symbology specification ISO/IEC 16390:2007 Information technology - Automatic identification and data capture techniques - Interleaved 2 of 5 bar code symbology specification ISO/TS 16401 Electronic fee collection – Evaluation of equipment for conformity to ISO/TS 17575-2 ISO/TS 16401-1:2012 Part 1: Test suite structure and test purposes ISO/TS 16401-2:2012 Part 2: Abstract test suite ISO 16402:2008 Implants for surgery – Acrylic resin cement – Flexural fatigue testing of acrylic resin cements used in orthopaedics ISO/TS 16407 Electronic fee collection – Evaluation of equipment for conformity to ISO/TS 17575-1 ISO/TS 16407-1:2011 Part 1: Test suite structure and test purposes ISO/TS 16407-2:2012 Part 2: Abstract test suite ISO/TS 16410 Electronic fee collection – Evaluation of equipment for conformity to ISO/TS 17575-3 ISO/TS 16410-1:2011 Part 1: Test suite structure and test purposes ISO/TS 16410-2:2012 Part 2: Abstract test suite ISO 16413:2013 Evaluation of thickness, density and interface width of thin films by X-ray reflectometry – Instrumental requirements, alignment and positioning, data collection, data analysis and reporting